DHCP三层交换机设置方式 全局模式和接口模式设置方式和命令接口模式和全局模式区别接口一旦换接口就要重新配置 全局的不用接口设置开启DHCP进接口开启dhcp select interface全局的需

.

DHCP三层交换机设置方式 全局模式和接口模式设置方式和命令

接口模式和全局模式区别

接口一旦换接口就要重新配置 全局的不用

接口设置
开启DHCP
进接口
开启dhcp select interface

全局的需要
开启dhcp
建池和池名称
设置网络段

进入接口设置ip address 192.168.10.1 24 设置ip地址
接口上dhcp select global 设置DHCP全局模式

reset save
回车
输入y
reboot
输入n
输入y
重启后就恢复默认设置了
默认用户名密码
admin
Admin@huawei

<DHCP>reset save y
<DHCP>reboot n y
恢复出厂设置

[DHCP]undo ip pool p4

[DHCP]int vlanif 10
[DHCP-Vlanif10]dhcp select interface //设置dhcp 接口模式
[DHCP-Vlanif10]int vlanif 20
[DHCP-Vlanif20]dhcp select interface
[DHCP-Vlanif20]int vlanif 30
[DHCP-Vlanif30]dhcp select interface
[DHCP-Vlanif30]int vlanif 40
[DHCP-Vlanif40]dhcp select interface
[DHCP-Vlanif40]q
[DHCP]dis current-configuration

[Huawei]sysname dhcp
[dhcp]vlan batch 10 20 30 40 创建vlan
Info: This operation may take a few seconds. Please wait for a moment...done.
[dhcp]port-group 1 创建组
[dhcp-port-group-1]group-member g0/0/1 g0/0/2 加入接口
[dhcp-port-group-1]port link-type trunk 设置trunk模式
[dhcp-GigabitEthernet0/0/1]port link-type trunk
[dhcp-GigabitEthernet0/0/2]port link-type trunk
[dhcp-port-group-1]port trunk allow-pass vlan all 设置全部vlan通过

[dhcp-GigabitEthernet0/0/1]port trunk allow-pass vlan all
[dhcp-GigabitEthernet0/0/2]port trunk allow-pass vlan all
[dhcp-port-group-1]q
[dhcp]dhcp enable 启用DHCP
Info: The operation may take a few seconds. Please wait for a moment.done.
[dhcp]ip pool p1 创建地址池p1
Info:It's successful to create an IP address pool.
[dhcp-ip-pool-p1]network 192.168.10.0 mask 24 设置网络段
[dhcp-ip-pool-p1]gateway-list 192.168.10.1 设置网关
[dhcp-ip-pool-p1]dns-list 1.1.1.1 设置dns服务器地址
[dhcp-ip-pool-p1]lease day 1 设置租约时间
[dhcp-ip-pool-p1]q
[dhcp]int vlanif 10 进入vlanif 10 虚拟接口
[dhcp-Vlanif10]ip address 192.168.10.1 24 设置ip地址
[dhcp-Vlanif10]dhcp select global 设置DHCP全局模式
后面设置 p2 p3 p4 vlanif 20 30 40 全部设置成功 完结

.