OSPF协议项目实战讲解-第一篇1、要求按照下列标准配置一个OSPF网络2、配置一个IP网络，实验逻辑图如图，IP地址见拓扑图3、路由协议采用OSPF，进程ID为1 ，RID为loopback0地址4
.
OSPF协议项目实战讲解-第一篇
1、要求按照下列标准配置一个OSPF网络
2、配置一个IP网络，实验逻辑图如图，IP地址见拓扑图
3、路由协议采用OSPF，进程ID为1 ，RID为loopback0地址
4、R1/R2/R3相连的三个站点链路OSPF网络类型配置成广播型，其中R1路由器做为永久性DR
5、按照图示配置OSPF区域，其中R2/R3/R4之间的区域要配置成完全末梢区域
6、R6为新并入的站点，由于来不及布线施工而暂时并到R5这个站点上，所在区域为AREA 56，配置使得所有网络可达(采用ping测试)
7、OSPF内部的网络希望通过R1路由器访问Internet，配置R1使其能够满足需求，只考虑内部路由器上路由的实现，不考虑NAT（下发默认路由）
8、AREA 0基于安全的原因配置上MD5认证，Key-ID为1，密码：Huawei
9、于R3与R4之间的链路质量较好，适当配置使得R4优先选取R3访问自身区域除外的外部网络
10、为了减少网络流量，R1只能学习到R6环回口的路由条目汇总条目（172.16.0.0/16）
1、要求按照下列标准配置一个OSPF网络
搭建拓扑图如下
2、配置一个IP网络，实验逻辑图如图，IP地址见拓扑图
R1的IP地址配置
# sysname R1#interface GigabitEthernet0/0/0 ip address 192.168.123.1 255.255.255.0 #interface LoopBack0 ip address 1.1.1.1 255.255.255.255 #R2的IP地址配置
# sysname R2#interface GigabitEthernet0/0/0 ip address 192.168.123.2 255.255.255.0 #interface GigabitEthernet0/0/1 ip address 192.168.24.2 255.255.255.0 #interface LoopBack0 ip address 2.2.2.2 255.255.255.255 #R3的IP地址配置
# sysname R3#interface GigabitEthernet0/0/0 ip address 192.168.123.3 255.255.255.0 #interface GigabitEthernet0/0/1 ip address 192.168.34.3 255.255.255.0 #interface GigabitEthernet0/0/2 ip address 192.168.35.3 255.255.255.0 #interface LoopBack0 ip address 3.3.3.3 255.255.255.255 #R4的IP地址配置
# sysname R4#interface GigabitEthernet0/0/0 ip address 192.168.24.4 255.255.255.0 #interface GigabitEthernet0/0/1 ip address 192.168.34.4 255.255.255.0 #interface LoopBack0 ip address 4.4.4.4 255.255.255.255 #R5的IP地址配置
# sysname R5#interface GigabitEthernet0/0/0 ip address 192.168.35.5 255.255.255.0 #interface GigabitEthernet0/0/1 ip address 192.168.56.5 255.255.255.0 #interface LoopBack0 ip address 5.5.5.5 255.255.255.255 #R6的IP地址配置
# sysname R6#interface GigabitEthernet0/0/0 ip address 192.168.56.6 255.255.255.0 #interface LoopBack0 ip address 192.168.3.1 255.255.255.0 #interface LoopBack1 ip address 172.16.1.1 255.255.255.0 #interface LoopBack2 ip address 172.16.2.1 255.255.255.0 #interface LoopBack3 ip address 172.16.3.1 255.255.255.0 #interface LoopBack4 ip address 172.16.4.1 255.255.255.0 #做完基本的IP地址配置后，大家可以自行ping通各自的直连网段
3、路由协议采用OSPF，进程ID为1 ，RID为loopback0地址
R1的OSPF配置
#ospf 1 router-id 1.1.1.1 area 0.0.0.0 network 1.1.1.1 0.0.0.0 network 192.168.123.0 0.0.0.255 #R2的OSPF配置
#ospf 1 router-id 2.2.2.2 area 0.0.0.0 network 2.2.2.2 0.0.0.0 network 192.168.123.0 0.0.0.255 area 0.0.0.234 network 192.168.24.0 0.0.0.255 #R3的OSPF配置
#ospf 1 router-id 3.3.3.3 area 0.0.0.0 network 3.3.3.3 0.0.0.0 network 192.168.123.0 0.0.0.255 area 0.0.0.234 network 192.168.34.0 0.0.0.255 area 0.0.0.35 network 192.168.35.0 0.0.0.255#R4的OSPF配置
#ospf 1 router-id 4.4.4.4 area 0.0.0.234 network 4.4.4.4 0.0.0.0 network 192.168.24.0 0.0.0.255 network 192.168.34.0 0.0.0.255 #R5的OSPF配置
#ospf 1 router-id 5.5.5.5 area 0.0.0.35 network 5.5.5.5 0.0.0.0 network 192.168.35.0 0.0.0.255 area 0.0.0.56 network 192.168.56.0 0.0.0.255 #R6的OSPF配置
#ospf 1 router-id 6.6.6.6 area 0.0.0.56 network 6.6.6.6 0.0.0.0 network 172.16.1.0 0.0.0.255 network 172.16.2.0 0.0.0.255 network 172.16.3.0 0.0.0.255 network 172.16.4.0 0.0.0.255 network 192.168.56.0 0.0.0.255 #检查
在R1上面检查如下
<R1>display ospf peer brief OSPF Process 1 with Router ID 1.1.1.1 Peer Statistic Information ---------------------------------------------------------------------------- Area Id Interface Neighbor id State 0.0.0.0 GigabitEthernet0/0/0 2.2.2.2 Full 0.0.0.0 GigabitEthernet0/0/0 3.3.3.3 Full ----------------------------------------------------------------------------在R2上面检查如下
<R2>display ospf peer brief OSPF Process 1 with Router ID 2.2.2.2 Peer Statistic Information ---------------------------------------------------------------------------- Area Id Interface Neighbor id State 0.0.0.0 GigabitEthernet0/0/0 1.1.1.1 Full 0.0.0.0 GigabitEthernet0/0/0 3.3.3.3 2-Way 0.0.0.234 GigabitEthernet0/0/1 4.4.4.4 Full ----------------------------------------------------------------------------因为R1为永久性DR，所以R2和R3是DROther
在R3上面检查如下
[R3]display ospf peer brief OSPF Process 1 with Router ID 3.3.3.3 Peer Statistic Information ---------------------------------------------------------------------------- Area Id Interface Neighbor id State 0.0.0.0 GigabitEthernet0/0/0 1.1.1.1 Full 0.0.0.0 GigabitEthernet0/0/0 2.2.2.2 2-Way 0.0.0.35 GigabitEthernet0/0/2 5.5.5.5 Full 0.0.0.234 GigabitEthernet0/0/1 4.4.4.4 Full ----------------------------------------------------------------------------在R4上面检查如下
<R4>display ospf peer brief OSPF Process 1 with Router ID 4.4.4.4 Peer Statistic Information ---------------------------------------------------------------------------- Area Id Interface Neighbor id State 0.0.0.234 GigabitEthernet0/0/0 2.2.2.2 Full 0.0.0.234 GigabitEthernet0/0/1 3.3.3.3 Full ----------------------------------------------------------------------------在R5上面检查如下
<R5>display ospf peer brief OSPF Process 1 with Router ID 5.5.5.5 Peer Statistic Information ---------------------------------------------------------------------------- Area Id Interface Neighbor id State 0.0.0.35 GigabitEthernet0/0/0 3.3.3.3 Full 0.0.0.56 GigabitEthernet0/0/1 6.6.6.6 Full ----------------------------------------------------------------------------在R6上面检查如下
<R6>display ospf peer brief OSPF Process 1 with Router ID 6.6.6.6 Peer Statistic Information ---------------------------------------------------------------------------- Area Id Interface Neighbor id State 0.0.0.56 GigabitEthernet0/0/0 5.5.5.5 Full ----------------------------------------------------------------------------此时发现R1 R2 R3 R4 R5之间都能够学习到各自的OSPF路由条目，R6由于没有按照正确的OSPF拓扑区域结构进行划分，导致R6不能够学习到任何其他设备的路由条目
4、R1/R2/R3相连的三个站点链路OSPF网络类型配置成广播型，其中R1路由器做为永久性DR
思路就是把R2和R3的接口优先级设置为0 OSPF的接口优先级的取值范围是0~255 当优先级为0的时候 代表本接口OSPF路由器不参与DR的选举，优先级为255就只代表优先级为255 这个和VRRP那个优先级要区分开来
#interface GigabitEthernet0/0/0 ospf dr-priority 0#在R1上面查看DR
<R1>display ospf interface GigabitEthernet 0/0/0 OSPF Process 1 with Router ID 1.1.1.1 Interfaces Interface: 192.168.123.1 (GigabitEthernet0/0/0) Cost: 1 State: DR Type: Broadcast MTU: 1500 Priority: 1 Designated Router: 192.168.123.1 Backup Designated Router: 0.0.0.0 Timers: Hello 10 , Dead 40 , Poll 120 , Retransmit 5 , Transmit Delay 1 5、按照图示配置OSPF区域，其中R2/R3/R4之间的区域要配置成完全末梢区域
R2的配置
#ospf 1 router-id 2.2.2.2 area 0.0.0.234 stub no-summary#R3的配置
#ospf 1 router-id 3.3.3.3area 0.0.0.234 stub no-summary#R4的配置
#ospf 1 router-id 4.4.4.4area 0.0.0.234 stub no-summary#检查：
[R4]display ospf lsdb OSPF Process 1 with Router ID 4.4.4.4 Link State Database Area: 0.0.0.234 Type LinkState ID AdvRouter Age Len Sequence Metric Router 4.4.4.4 4.4.4.4 43 60 8000000B 1 Router 2.2.2.2 2.2.2.2 1553 36 80000003 1 Router 3.3.3.3 3.3.3.3 1553 36 80000003 1 Network 192.168.24.4 4.4.4.4 1552 32 80000001 0 Network 192.168.34.4 4.4.4.4 1552 32 80000001 0 Sum-Net 0.0.0.0 3.3.3.3 1561 28 80000001 1 Sum-Net 0.0.0.0 2.2.2.2 1562 28 80000001 1[R4]display ip routing-table Route Flags: R - relay, D - download to fib------------------------------------------------------------------------------Routing Tables: Public Destinations : 12 Routes : 13 Destination/Mask Proto Pre Cost Flags NextHop Interface 0.0.0.0/0 OSPF 10 2 D 192.168.34.3 GigabitEthernet0/0/1 OSPF 10 2 D 192.168.24.2 GigabitEthernet0/0/0 4.4.4.4/32 Direct 0 0 D 127.0.0.1 LoopBack0 127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0 127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0 192.168.24.0/24 Direct 0 0 D 192.168.24.4 GigabitEthernet0/0/0 192.168.24.4/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0 192.168.24.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0 192.168.34.0/24 Direct 0 0 D 192.168.34.4 GigabitEthernet0/0/1 192.168.34.4/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1 192.168.34.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0[R4]6、R6为新并入的站点，由于来不及布线施工而暂时并到R5这个站点上，所在区域为AREA 56，配置使得所有网络可达(采用ping测试)
R3的配置如下
#ospf 1 router-id 3.3.3.3 area 0.0.0.35 network 192.168.35.0 0.0.0.255 vlink-peer 5.5.5.5#R5的配置如下
#ospf 1 router-id 5.5.5.5area 0.0.0.35 network 192.168.35.0 0.0.0.255 vlink-peer 3.3.3.3#检查
<R3>display ospf vlink OSPF Process 1 with Router ID 3.3.3.3 Virtual Links Virtual-link Neighbor-id -> 5.5.5.5, Neighbor-State: Full Interface: 192.168.35.3 (GigabitEthernet0/0/2) Cost: 1 State: P-2-P Type: Virtual Transit Area: 0.0.0.35 Timers: Hello 10 , Dead 40 , Retransmit 5 , Transmit Delay 1 GR State: Normal <R5>display ospf vlink OSPF Process 1 with Router ID 5.5.5.5 Virtual Links Virtual-link Neighbor-id -> 3.3.3.3, Neighbor-State: Full Interface: 192.168.35.5 (GigabitEthernet0/0/0) Cost: 1 State: P-2-P Type: Virtual Transit Area: 0.0.0.35 Timers: Hello 10 , Dead 40 , Retransmit 5 , Transmit Delay 1 GR State: Normal检查一下路由情况
在R1这边查看172网段的路由情况
<R1>display ospf lsdb OSPF Process 1 with Router ID 1.1.1.1 Link State Database Area: 0.0.0.0 Type LinkState ID AdvRouter Age Len Sequence Metric Router 2.2.2.2 2.2.2.2 234 48 80000009 1 Router 1.1.1.1 1.1.1.1 232 48 80000007 1 Router 5.5.5.5 5.5.5.5 223 36 80000003 1 Router 3.3.3.3 3.3.3.3 236 60 80000010 1 Network 192.168.123.1 1.1.1.1 232 36 80000003 0 Sum-Net 192.168.56.0 5.5.5.5 233 28 80000002 1 Sum-Net 5.5.5.5 3.3.3.3 233 28 80000002 1 Sum-Net 5.5.5.5 5.5.5.5 233 28 80000002 0 Sum-Net 192.168.35.0 3.3.3.3 279 28 80000002 1 Sum-Net 192.168.35.0 5.5.5.5 233 28 80000002 1 Sum-Net 172.16.3.1 5.5.5.5 17 28 80000001 1 Sum-Net 192.168.34.0 3.3.3.3 272 28 80000002 1 Sum-Net 192.168.34.0 2.2.2.2 220 28 80000002 2 Sum-Net 172.16.2.1 5.5.5.5 17 28 80000001 1 Sum-Net 192.168.24.0 2.2.2.2 272 28 80000002 1 Sum-Net 192.168.24.0 3.3.3.3 515 28 80000002 2 Sum-Net 172.16.1.1 5.5.5.5 17 28 80000001 1 Sum-Net 4.4.4.4 3.3.3.3 225 28 80000002 1 Sum-Net 4.4.4.4 2.2.2.2 220 28 80000002 1 Sum-Net 172.16.4.1 5.5.5.5 17 28 80000001 1在R3这边查看OSPF的LSDB
[R3]display ospf lsdb OSPF Process 1 with Router ID 3.3.3.3 Link State Database Area: 0.0.0.0 Type LinkState ID AdvRouter Age Len Sequence Metric Router 2.2.2.2 2.2.2.2 251 48 80000009 1 Router 1.1.1.1 1.1.1.1 249 48 80000007 1 Router 5.5.5.5 5.5.5.5 238 36 80000003 1 Router 3.3.3.3 3.3.3.3 251 60 80000010 1 Network 192.168.123.1 1.1.1.1 249 36 80000003 0 Sum-Net 192.168.56.0 5.5.5.5 248 28 80000002 1 Sum-Net 5.5.5.5 3.3.3.3 247 28 80000002 1 Sum-Net 5.5.5.5 5.5.5.5 248 28 80000002 0 Sum-Net 192.168.35.0 3.3.3.3 293 28 80000002 1 Sum-Net 192.168.35.0 5.5.5.5 248 28 80000002 1 Sum-Net 172.16.3.1 5.5.5.5 32 28 80000001 1 Sum-Net 192.168.34.0 3.3.3.3 286 28 80000002 1 Sum-Net 192.168.34.0 2.2.2.2 237 28 80000002 2 Sum-Net 172.16.2.1 5.5.5.5 32 28 80000001 1 Sum-Net 192.168.24.0 2.2.2.2 289 28 80000002 1 Sum-Net 192.168.24.0 3.3.3.3 530 28 80000002 2 Sum-Net 172.16.1.1 5.5.5.5 32 28 80000001 1 Sum-Net 4.4.4.4 3.3.3.3 239 28 80000002 1 Sum-Net 4.4.4.4 2.2.2.2 237 28 80000002 1 Sum-Net 172.16.4.1 5.5.5.5 32 28 80000001 1 Area: 0.0.0.35 Type LinkState ID AdvRouter Age Len Sequence Metric Router 5.5.5.5 5.5.5.5 238 48 8000000B 1 Router 3.3.3.3 3.3.3.3 251 36 80000007 1 Network 192.168.35.5 5.5.5.5 248 32 80000002 0 Sum-Net 192.168.56.0 5.5.5.5 248 28 80000002 1 Sum-Net 192.168.123.0 3.3.3.3 293 28 80000002 1 Sum-Net 3.3.3.3 3.3.3.3 295 28 80000002 0 Sum-Net 172.16.3.1 5.5.5.5 34 28 80000001 1 Sum-Net 192.168.34.0 3.3.3.3 288 28 80000002 1 Sum-Net 172.16.2.1 5.5.5.5 34 28 80000001 1 Sum-Net 192.168.24.0 3.3.3.3 532 28 80000005 2 Sum-Net 172.16.1.1 5.5.5.5 34 28 80000001 1 Sum-Net 4.4.4.4 3.3.3.3 241 28 80000002 1 Sum-Net 2.2.2.2 3.3.3.3 249 28 80000002 1 Sum-Net 172.16.4.1 5.5.5.5 34 28 80000001 1 Sum-Net 1.1.1.1 3.3.3.3 249 28 80000002 1 Sum-Asbr 1.1.1.1 3.3.3.3 249 28 80000002 1 Area: 0.0.0.234 Type LinkState ID AdvRouter Age Len Sequence Metric Router 4.4.4.4 4.4.4.4 533 60 8000000B 1 Router 2.2.2.2 2.2.2.2 244 36 80000004 1 Router 3.3.3.3 3.3.3.3 241 36 80000004 1 Network 192.168.24.4 4.4.4.4 243 32 80000002 0 Network 192.168.34.4 4.4.4.4 244 32 80000002 0 Sum-Net 0.0.0.0 3.3.3.3 249 28 80000002 1 Sum-Net 0.0.0.0 2.2.2.2 253 28 80000002 17、OSPF内部的网络希望通过R1路由器访问Internet，配置R1使其能够满足需求，只考虑内部路由器上路由的实现，不考虑NAT（下发默认路由）
在R1上面配置静态路由 然后下发其静态路由
ip route-static 0.0.0.0 0.0.0.0 192.168.60.1#ospf 1 router-id 1.1.1.1 default-route-advertise area 0.0.0.0 #检查
在R2 R3 R5 R6上面查看路由表
<R2>display ip routing-table protocol ospf Route Flags: R - relay, D - download to fib------------------------------------------------------------------------------Public routing table : OSPF Destinations : 12 Routes : 12 OSPF routing table status : <Active> Destinations : 12 Routes : 12Destination/Mask Proto Pre Cost Flags NextHop Interface 0.0.0.0/0 O_ASE 150 1 D 192.168.123.1 GigabitEthernet0/0/0 1.1.1.1/32 OSPF 10 1 D 192.168.123.1 GigabitEthernet0/0/0 3.3.3.3/32 OSPF 10 1 D 192.168.123.3 GigabitEthernet0/0/0 4.4.4.4/32 OSPF 10 1 D 192.168.24.4 GigabitEthernet0/0/1 5.5.5.5/32 OSPF 10 2 D 192.168.123.3 GigabitEthernet0/0/0 172.16.1.1/32 OSPF 10 3 D 192.168.123.3 GigabitEthernet0/0/0 172.16.2.1/32 OSPF 10 3 D 192.168.123.3 GigabitEthernet0/0/0 172.16.3.1/32 OSPF 10 3 D 192.168.123.3 GigabitEthernet0/0/0 172.16.4.1/32 OSPF 10 3 D 192.168.123.3 GigabitEthernet0/0/0 192.168.34.0/24 OSPF 10 2 D 192.168.24.4 GigabitEthernet0/0/1 192.168.35.0/24 OSPF 10 2 D 192.168.123.3 GigabitEthernet0/0/0 192.168.56.0/24 OSPF 10 3 D 192.168.123.3 GigabitEthernet0/0/0OSPF routing table status : <Inactive> Destinations : 0 Routes : 08、AREA 0基于安全的原因配置上MD5认证，Key-ID为1，密码：Huawei
在R1的区域0中配置区域0的认证
#ospf 1 router-id 1.1.1.1 area 0.0.0.0 authentication-mode md5 1 plain Huawei#在R2的区域0中配置区域0的认证
#ospf 1 router-id 2.2.2.2area 0.0.0.0 authentication-mode md5 1 plain Huawei#在R3的区域0中配置区域0的认证
#ospf 1 router-id 3.3.3.3area 0.0.0.0 authentication-mode md5 1 plain Huawei#在R5的区域0中配置区域0的认证
#ospf 1 router-id 5.5.5.5area 0.0.0.0 authentication-mode md5 1 plain Huawei#或者第二种方法：
#ospf 1 router-id 5.5.5.5 area 0.0.0.0 area 0.0.0.35 network 5.5.5.5 0.0.0.0 network 192.168.35.0 0.0.0.255 vlink-peer 3.3.3.3 md5 1 plain Huawei 直接在后面接上认证的参数也是可以的 area 0.0.0.56 network 192.168.56.0 0.0.0.255 #检查 看下 R5和R3之间的FULL关系是否正常
9、于R3与R4之间的链路质量较好，适当配置使得R4优先选取R3访问自身区域除外的外部网络
在R4的G0/0/0接口修改OSPF的开销值
[R4-GigabitEthernet0/0/0]dis this[V200R003C00]#interface GigabitEthernet0/0/0 ip address 192.168.24.4 255.255.255.0 ospf cost 2#检查
[R4]display ip routing-table Route Flags: R - relay, D - download to fib------------------------------------------------------------------------------Routing Tables: Public Destinations : 12 Routes : 12 Destination/Mask Proto Pre Cost Flags NextHop Interface 0.0.0.0/0 OSPF 10 2 D 192.168.34.3 GigabitEthernet0/0/1 4.4.4.4/32 Direct 0 0 D 127.0.0.1 LoopBack0 127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0 127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0 192.168.24.0/24 Direct 0 0 D 192.168.24.4 GigabitEthernet0/0/0 192.168.24.4/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0 192.168.24.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/0 192.168.34.0/24 Direct 0 0 D 192.168.34.4 GigabitEthernet0/0/1 192.168.34.4/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1 192.168.34.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack010、为了减少网络流量，R1只能学习到R6环回口的路由条目汇总条目（172.16.0.0/16）
在R5的区域56当中进行路由汇总
#ospf 1 router-id 5.5.5.5 area 0.0.0.56 abr-summary 172.16.0.0 255.255.0.0#return检查如下
[R1]dis ip routing-table protocol ospf Route Flags: R - relay, D - download to fib------------------------------------------------------------------------------Public routing table : OSPF Destinations : 9 Routes : 10 OSPF routing table status : <Active> Destinations : 9 Routes : 10Destination/Mask Proto Pre Cost Flags NextHop Interface 2.2.2.2/32 OSPF 10 1 D 192.168.123.2 GigabitEthernet0/0/0 3.3.3.3/32 OSPF 10 1 D 192.168.123.3 GigabitEthernet0/0/0 4.4.4.4/32 OSPF 10 2 D 192.168.123.3 GigabitEthernet0/0/0 OSPF 10 2 D 192.168.123.2 GigabitEthernet0/0/0 5.5.5.5/32 OSPF 10 2 D 192.168.123.3 GigabitEthernet0/0/0 172.16.0.0/16 OSPF 10 3 D 192.168.123.3 GigabitEthernet0/0/0 192.168.24.0/24 OSPF 10 2 D 192.168.123.2 GigabitEthernet0/0/0 192.168.34.0/24 OSPF 10 2 D 192.168.123.3 GigabitEthernet0/0/0 192.168.35.0/24 OSPF 10 2 D 192.168.123.3 GigabitEthernet0/0/0 192.168.56.0/24 OSPF 10 3 D 192.168.123.3 GigabitEthernet0/0/0OSPF routing table status : <Inactive> Destinations : 0 Routes : 0