shijitianle#erase flash data ? --------------------------------------------- Command of privile
.
shijitianle#erase flash data ? --------------------------------------------- Command of privilege Mode:---------------------------------------------Options<E><active,standby> Active board or standby board#第一步 清空standby数据shijitianle#erase flash data standby ?--------------------------------------------- Command of privilege Mode:---------------------------------------------<cr> Please press ENTER to execute command shijitianle#erase flash data standby This command will clear the standby board data has been loaded or saved Are you sure to continue? (y/n)[n]:y Command executes successfully, and will take effect after standby board rebootedshijitianle#shijitianle#shijitianle#shijitianle##第二步 清空active数据shijitianle#erase flash data active ?--------------------------------------------- Command of privilege Mode:---------------------------------------------<cr> Please press ENTER to execute command shijitianle#erase flash data active This command will clear the active board data that has been loaded or saved Please remember to backup the system configuration data Are you sure to continue? (y/n)[n]:y Command executes successfully, and will take effect after active board rebootedshijitianle#shijitianle#shijitianle##第三步 重启系统shijitianle#reboot ?--------------------------------------------- Command of privilege Mode:---------------------------------------------Options<E><system,active,standby> System reboot or reset active board or reset standby boardshijitianle#reboot system ?--------------------------------------------- Command of privilege Mode:---------------------------------------------<cr> Please press ENTER to execute command shijitianle#reboot system Please check whether data has saved, the unsaved data will lose if reboot system, are you sure to reboot system? (y/n)[n]:y #输入yshijitianle# Platform System start ... Memory Data Bus Test .................pass. Memory Address Bus Test ..............pass. Press 'Ctrl+T' To Start Memory Complete Test Trace code : 0x00000000 Copy from ROM to RAM ...... OK! Uncompress from ROM to RAM ...... OK! Update fpga...OK. Copyright (c) 1998 - 2013 by Huawei Technologies Co.,Ltd. All Rights Reserved. The last update date of base BIOS B is : Aug 26 2013 08:21:05 =============================================================== BOARD INFORMATION : CPU: P2010. Processor #1.(Rev 5.01) running at 1200Mhz 1024M bytes DDR(ECC), 256M bytes flash installed on board Baudrate of serial channel is 9600bps Board's LAN IP address is 10.11.104.2 Board's LAN Subnet mask is 255.255.255.0 Board's LAN MAC address is 24:9E:AB:B7:9F:B1 =============================================================== Base BIOS version is 309 Save extended BIOS disable start flag...OK! Transferring control to the extended BIOS ...OK! System Vfs init...OK The last update date of extended BIOS is : Mar 22 2013 17:46:38 System is booting from extended BIOS... Extended BIOS version is 312 Press <D> key to stop auto-boot 0 Now system will boot from flash memory. Testing Flash memory...OK! Select area information : Program Area B ,Data Area B . Begin to expand program... OK! Save extended BIOS enable start flag...OK! Transferring control to the loaded program...OK! Starting system application init......successfully! Starting system configuration data init...successfully! Press any key to get started>>User name:root>>User password: Huawei Integrated Access Software. Copyright(C) Huawei Technologies Co., Ltd. 2002-2012. All rights reserved. User root has used a default password. Change the password in time.MA5680T>enableMA5680T#MA5680T#MA5680T#display current-configuration { <cr>|ont<K>|port<K>|section<K>|service-port<K>|simple<K>||<K> }: Command: display current-configuration Failure: The system is saving or backing up the data, please try later 这里系统启动起来，active和standby需要时间同步一下信息，所以需要等几分钟再进行操作。默认仅有的配置。MA5680T#display current-configuration{ <cr>|ont<K>|port<K>|section<K>|service-port<K>|simple<K>||<K> }: Command: display current-configuration [MA5600V800R011: 5800]#[sysmode] <sysmode> switch adsl mode to rfc2662 vdsl mode to tr129 xpon mode switch-to profile-mode protocol support h248 system ex-mode backup #[global-config] <global-config> event output eventid 0x023000f1 event eventlevel 0x023000f1 minor alarm output alarmid 0x64110001 alarm output alarmid 0x64120001 ont-lineprofile gpon profile-id 0 profile-name "line-profile_default_0" tr069-management ip-index 0 tcont 0 dba-profile-id 2 tcont 1 dba-profile-id 0 commit quit#[device-config] <device-config> board add standby rack info 0 description "RACK-300" name "RACK-300" manufactured-name "Huawei"#[public-config] <public-config> snmp-agent local-engineid 800007DB03249EABB79FB15A#[emu-config] <emu-config> emu add 0 fan 0 1 "H801FCBC"#[config] <config> mpls label start 8192#[meth] <meth0>interface meth0 ip address 10.11.104.2 255.255.255.0#[null] <null0>interface null0# [aaa] <aaa>aaa authentication-scheme "default" # authorization-scheme "default" # accounting-scheme "default" # domain "default" #return